Sharpen Your Knowledge with Cisco CCNP Routing and Switching (300-135) Certification Sample Questions
CertsTime has provided you with a sample question set to elevate your knowledge about the Cisco Troubleshooting and Maintaining Cisco IP Networks exam. With these updated sample questions, you can become quite familiar with the difficulty level and format of the real 300-135 certification test. Try our sample Cisco Troubleshooting and Maintaining Cisco IP Networks certification practice exam to get a feel for the real exam environment. Our sample practice exam gives you a sense of reality and an idea of the questions on the actual Cisco Certified Network Professional Routing and Switching certification exam.
Our sample questions are similar to the Real Cisco CCNP Routing and Switching TSHOOT 300-135 exam questions. The premium Cisco Troubleshooting and Maintaining Cisco IP Networks certification practice exam gives you a golden opportunity to evaluate and strengthen your preparation with real-time scenario-based questions. Plus, by practicing real-time scenario-based questions, you will run into a variety of challenges that will push you to enhance your knowledge and skills.
Cisco 300-135 Sample Questions:
Refer to the exhibit.
Which command can be used to apply the INTERNET ACL to an interface in order for traffic to pass?
You work as Network Engineer for RADO network Ltd company. You colleague has setup POC simulating customer network to study about the behavior of BGP protocol when routes are exchanged between two different autonomous systems.
Review the topology. You need to identify and fix IBGP and EBGP issues on R1 router.
Topology Details:
AS64520
* R1, R2 and R3 are three routers on AS 64520 and OSPF is IGP routing protocol configured between them.
* IBGP configured between R1, R2, and R3 routers using peer group.
* Loopback0 address is used for IBGP peering, Loopback0 address configured on R1, R2 and R3 are advertised into BGP domain on AS64525.
AS64525
* RA and RB are two routers on AS64525 and EIGRP is IGP routing protocol configured between them.
* Loopback0 address is used for IBGP peering, Loopback0 address configured on RA and RB advertised into BGP domain on AS64525.
* R1 and RRA from EBGP neighbor relationship using physical interface address.
*R2 and RB from EBGP neighbor relationship using physical interface address.
Simulation requirements:
*Identify and fix EBGP neighbor relationship between R1 and R1 routers.
*Identify and fix IBGP neighbor relationship issue between R1 and R2, R1 and R3.
*You are allowed to remove any misconfiguration or incorrect configuration to only fix the issue and other initial configuration that not impacting the issues should not be changed.
* The Final BGP table, after fixing two issues on R1 router should display as shown below
The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
Use the supported commands to isolate the cause of this fault and answer the following question.
What is the solution to the fault condition?
The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
The fault condition is related to which technology?
The implementation group has been using the test bed to do an IPv6 'proof-of-concept1. After several changes to the network addressing and routing schemes, a trouble ticket has been opened indicating that the loopback address on R1 (2026::111:1) is not able to ping the loopback address on DSW2 (2026::102:1).
Use the supported commands to isolate the cause of this fault and answer the following question.
On which device is the fault condition located?
Note: If there is any error in our Cisco 300-135 certification exam sample questions, please update us via email at support@certstime.com.